Coppell, Dallas County
Broken Spring Repair in Coppell, TX
The sound is unmistakable and homeowners describe it the same way every time: a bang from the garage loud enough to be mistaken for a gunshot, and afterward a door that will not lift. That is a torsion spring releasing its stored energy at once, and it is the most common single failure we replace in Coppell.
- Same-day service available
- 10+ years serving Dallas
- Free on-site estimates
- 15% off current repairs
How a torsion spring stores and returns energy
A torsion spring sits on a steel shaft above the door opening. Installing it means winding it a specific number of turns, commonly around seven and a half for a seven foot door, which twists the spring steel and stores mechanical energy in it. Cables run from drums at each end of that shaft down to brackets at the bottom corners of the door. As the door closes, the door's own weight winds the spring tighter; as it opens, the spring unwinds and returns that stored energy to the drums, which pull the cables and lift the door. The system is designed so that the spring's torque and the door's weight cancel out, which is why a healthy door can be lifted with about ten pounds of hand effort despite weighing well over a hundred.
Why we replace both springs, not just the broken one
On a two spring door, both springs were installed on the same day and have taken the same number of cycles. When one reaches the end of its fatigue life, the other is within a short distance of the same point. Replacing only the failed spring gives you a door with one new spring and one old one, an unequal torque distribution across the shaft, and a second service call in the near future for the same problem. There is also a sizing consequence: springs are selected as a matched pair for the door weight, and a mismatched pair never balances the door correctly across its travel. Replacing both at once costs less than two visits and produces a door that actually balances.
Sizing is measurement, not estimation
A torsion spring is defined by four values: wire diameter, inside diameter, overall length, and wind direction. Those combine to determine how much torque the spring produces per turn. Selecting a replacement means knowing the door's weight, either by weighing it on a scale with the springs disconnected or by calculating from section construction, glazing, and hardware. A spring undersized for the door leaves the door heavy at the floor and burns cycles fast. A spring oversized for it leaves the door wanting to fly open and makes the opener fight it on the way down. Both feel roughly acceptable on the day of installation, and both shorten the life of everything they are attached to.
Broken Spring Repair for Coppell homes
Almost entirely built out between 1985 and 2000, giving the city an unusually uniform stock of two- and three-car attached garages whose original openers and springs are now aging out together.
Our route through Coppell takes in 75019.
Regular calls come from Riverchase, Old Town Coppell and Northlake Woodlands.
If you are near Andrew Brown Park, you are well inside our route.
Coppell is a Dallas County community of roughly 41,785.
Please do not attempt this one yourself
A torsion spring holds several hundred pounds of stored energy even when the door is down. Releasing that energy without the correct winding bars is how people lose fingers. If a spring has snapped, leave the door closed and call us.
What you are probably seeing
- The top section flexes or bends when the opener tries to lift the door.
- The cables have gone slack or come off the drums after the failure.
- A gap has opened between coils on an intact spring, or the coils show rust pitting.
- A loud bang from the garage, often heard from inside the house, with the door working fine right up until that moment.
- A visible gap of two to three inches in the coil of the spring above the door.
Coppell service
Call (469) 891-6883 or request a visit.
The visit
How a Coppell call runs
Confirm the failure and secure the door
We identify which spring broke, check whether the intact spring is still under load, and secure the door so it cannot move while work is underway. The opener stays disconnected for the duration.
Measure the door and the existing springs
Wire diameter, inside diameter, length, and wind direction are recorded from the existing springs, and the door weight is established. Those numbers determine the replacement rather than a visual match.
Controlled removal
Any remaining tension is unwound with proper winding bars, cables are released from the drums, and the old springs come off the shaft. Bearings, drums, and the shaft itself are inspected while they are accessible, since this is the only convenient time to see them.
Install and wind to calculated turns
New springs of the correct specification are installed as a pair, cables are set in the drums with equal tension so the door lifts square, and the springs are wound to the turn count the door requires rather than to a default.
Balance test and opener reset
The door is lifted by hand and checked at several points in travel to confirm it holds position. The opener is reconnected, travel and force are reset to the corrected door, and the safety reversal is tested.
On the job
Broken Spring Repair in the field
Questions
Broken Spring Repair in Coppell
Can I replace a torsion spring myself?
We will not encourage it, and this is the one place on this site where the recommendation is unqualified. Winding a torsion spring requires correctly sized steel winding bars, properly seated cone set screws, and a technique that keeps your body out of the arc of the bars. Improvised tools slipping under several hundred pounds of torque cause hand, wrist, and facial injuries every year. Almost everything else on a garage door is a reasonable DIY project. This is not.
How long should a new spring last?
Divide the spring's cycle rating by your daily cycles and multiply out. A standard 10,000 cycle spring lasts roughly four to five years at six cycles a day, or fourteen years at two. If your household is at the high end of usage, high cycle springs at 20,000 or more are a reasonable upgrade and the price difference is modest relative to a second replacement.
Can I still get my car out with a broken spring?
Sometimes, with help, and carefully. With the opener released, the door weighs its full weight, which on a double door is often over 200 pounds. Two adults can usually manage it and it should be propped securely with something solid, never a person's hands, while a vehicle passes underneath. Do not run the opener, because that is how a spring failure becomes a cable, drum, and opener failure.
Did I do something to cause this?
Almost certainly not. Springs fail from metal fatigue accumulated over a counted number of cycles, and the failure typically lands on a cold morning because the steel is slightly less forgiving then. The two things that genuinely shorten spring life are a spring undersized for the door at installation and corrosion pitting on the coil, and neither is caused by how you use the door.
Does a broken spring damage the opener?
Running the door on a broken spring will, given enough attempts. The opener suddenly has to move the full weight of the door, and what fails is the drive gear, the trolley, the opener arm, or the top section where the arm attaches. One or two attempts before you realize what happened is usually harmless. Repeated cycling is not.
Need this handled today?
Broken Spring Repair in Coppell and across Dallas County.