Argyle, Denton County
Broken Spring Repair in Argyle, TX
Most spring replacements in Argyle are completed within an hour to ninety minutes of arrival, because the truck carries the common wire sizes and lengths. The visit ends with the door balanced by hand and the opener's force reset to the corrected door rather than the broken one.
- Same-day service available
- 10+ years serving Dallas
- Free on-site estimates
- 15% off current repairs
Why a broken one is dangerous to work on
The danger is not the broken spring, which has already released. The danger is everything else still under load. On a two spring door, the intact spring is still fully wound. The cables are still anchored to bottom brackets that are under the full tension of that counterbalance, which is why those brackets carry a warning label from the factory. Winding or unwinding a torsion spring is done with steel winding bars inserted into the holes of the winding cone; if a bar is the wrong diameter, if the set screws are not properly seated, or if a hand slips, the bar comes out of the cone at speed with several hundred pounds of torque behind it. Emergency departments see these injuries regularly, and they are typically hand, wrist, facial, and dental. Screwdrivers and lengths of rebar used in place of proper winding bars are how most of them happen.
Torsion and extension springs are different systems
Torsion springs mount on a shaft above the opening and are standard on most doors installed in the last few decades. Extension springs run horizontally along the tracks on each side, stretch as the door closes, and contract to help lift it. Extension springs are still common on older and lighter doors, and they carry a specific hazard: without a safety cable threaded through the center of the spring and anchored at both ends, a failing extension spring becomes a whipping length of steel across the garage. If your door has extension springs and no safety cables, adding them is inexpensive and we will recommend it whether or not the spring has failed.
Sizing is measurement, not estimation
A torsion spring is defined by four values: wire diameter, inside diameter, overall length, and wind direction. Those combine to determine how much torque the spring produces per turn. Selecting a replacement means knowing the door's weight, either by weighing it on a scale with the springs disconnected or by calculating from section construction, glazing, and hardware. A spring undersized for the door leaves the door heavy at the floor and burns cycles fast. A spring oversized for it leaves the door wanting to fly open and makes the opener fight it on the way down. Both feel roughly acceptable on the day of installation, and both shorten the life of everything they are attached to.
Broken Spring Repair for Argyle homes
Horse-country lots with large custom homes, so three- and four-car garages plus barn and shop doors sized for tractors and trailers make up a big share of the work here.
That ZIP code are ours: 76226.
We are in Country Lakes, Harvest and Canyon Falls most weeks.
Anywhere around Argyle Town Hall is a short run for us.
Argyle sits in Denton County with a population of about 6,294.
Please do not attempt this one yourself
A torsion spring holds several hundred pounds of stored energy even when the door is down. Releasing that energy without the correct winding bars is how people lose fingers. If a spring has snapped, leave the door closed and call us.
What you are probably seeing
- The opener strains, moves the door a few inches, and stops or reverses.
- The door is extremely heavy to lift by hand and will not stay up when released.
- The door rises crooked, with one side lagging behind the other.
- The top section flexes or bends when the opener tries to lift the door.
- The cables have gone slack or come off the drums after the failure.
Argyle service
Call (469) 891-6883 or request a visit.
The visit
How a Argyle call runs
Confirm the failure and secure the door
We identify which spring broke, check whether the intact spring is still under load, and secure the door so it cannot move while work is underway. The opener stays disconnected for the duration.
Measure the door and the existing springs
Wire diameter, inside diameter, length, and wind direction are recorded from the existing springs, and the door weight is established. Those numbers determine the replacement rather than a visual match.
Controlled removal
Any remaining tension is unwound with proper winding bars, cables are released from the drums, and the old springs come off the shaft. Bearings, drums, and the shaft itself are inspected while they are accessible, since this is the only convenient time to see them.
Install and wind to calculated turns
New springs of the correct specification are installed as a pair, cables are set in the drums with equal tension so the door lifts square, and the springs are wound to the turn count the door requires rather than to a default.
Balance test and opener reset
The door is lifted by hand and checked at several points in travel to confirm it holds position. The opener is reconnected, travel and force are reset to the corrected door, and the safety reversal is tested.
On the job
Broken Spring Repair in the field
Questions
Broken Spring Repair in Argyle
Can I replace a torsion spring myself?
We will not encourage it, and this is the one place on this site where the recommendation is unqualified. Winding a torsion spring requires correctly sized steel winding bars, properly seated cone set screws, and a technique that keeps your body out of the arc of the bars. Improvised tools slipping under several hundred pounds of torque cause hand, wrist, and facial injuries every year. Almost everything else on a garage door is a reasonable DIY project. This is not.
Why do I have to replace both springs?
Because both have taken the same number of cycles and the second one is close behind the first. Beyond that, springs are sized as a matched pair against the door weight, and a new spring paired with a fatigued one distributes torque unevenly across the shaft, so the door never balances properly through its travel. Two visits also cost more than one.
Will you replace the cables at the same time?
We inspect them and tell you what we find. Cables that show fraying at the drum wrap or at the bottom bracket are worth replacing while the spring work already has the system apart, because the labor overlaps almost entirely. Cables in good condition do not need replacing simply because a spring failed.
Does a broken spring damage the opener?
Running the door on a broken spring will, given enough attempts. The opener suddenly has to move the full weight of the door, and what fails is the drive gear, the trolley, the opener arm, or the top section where the arm attaches. One or two attempts before you realize what happened is usually harmless. Repeated cycling is not.
Do you carry springs on the truck or does it take a second visit?
Common residential wire sizes and lengths are carried, so the large majority of replacements are completed on the first visit. Unusual sizes, very heavy custom doors, and some high cycle configurations occasionally need to be ordered, and we tell you at diagnosis if yours is one of them.
Book a visit that fits your day
Broken Spring Repair in Argyle and across Denton County.