McKinney, Collin County
Broken Cable Repair in McKinney, TX
Cable replacement is one of the least expensive repairs on a garage door and one of the most expensive to postpone. A door running on one cable twists in the tracks, gouges the vertical track, bends the bottom bracket, and can pull rollers out entirely, and at that point the invoice in McKinney is no longer about a cable.
- Same-day service available
- 10+ years serving Dallas
- Free on-site estimates
- 15% off current repairs
What the lift cables do and where they run
On a torsion door, a grooved drum sits at each end of the spring shaft above the opening. A steel aircraft cable winds around each drum, runs down the inside of the vertical track, and terminates at a bottom bracket bolted to the lowest corner of the door. When the springs unwind, they rotate the shaft, the drums take up cable, and the cable lifts the door. The cables carry the entire weight of the door in tension. They are not a secondary or a safety component; they are the connection between the counterbalance and the door itself, and when one fails that side of the door has nothing holding it.
Why cables fray at the drum
A cable does not wear evenly along its length. It wears where it bends under load. At the drum, the cable wraps a tight radius, and each cycle it lays into the groove, takes the full tension, and unwinds again, flexing the individual strands against each other and against the drum surface. Any misalignment makes it worse: a drum set screw that has crept loose lets the drum shift on the shaft, the cable then rides on the drum flange rather than seating in the groove, and it saws against the edge. The same principle applies at the bottom bracket, where the cable loops through a fitting and takes a sharp turn under full load. Those two points account for nearly every cable failure we see.
The bottom bracket is where people get hurt
Both bottom brackets are under the full tension of the counterbalance whenever the door is closed, because that is exactly where the cables pull. Factory labels on those brackets warn against removing them, and the warning is accurate. If the bolts are backed out while the springs are wound, the bracket departs the door under load with the cable attached. Correct sequence is to unwind the springs with winding bars first, so the cables go slack, and only then work on the bracket. This is the same reason a broken cable is not a job to improvise on a Saturday: the intact side is still fully loaded.
Broken Cable Repair for McKinney homes
Two very different jobs in one city: century-old homes around the square with detached alley garages and shallow headers, and Stonebridge Ranch and Craig Ranch homes with three-car attached bays.
We cover ZIP codes 75069, 75070, 75071 and 75072.
Historic Downtown, Stonebridge Ranch and Craig Ranch account for a steady share of our McKinney work.
Historic Downtown McKinney Square is a useful marker: if you are near it, we cover you.
About 227,526 people live in McKinney, in Collin County.
Please do not attempt this one yourself
A torsion spring holds several hundred pounds of stored energy even when the door is down. Releasing that energy without the correct winding bars is how people lose fingers. If a spring has snapped, leave the door closed and call us.
What you are probably seeing
- One corner of the door hangs lower than the other, whether open or closed.
- A cable is visibly loose, hanging slack, or coiled off the drum.
- You can see broken strands sticking out of the cable, often described as fuzzy or whiskered.
- The door lifts unevenly and binds partway up.
- Loud scraping or popping from one side of the door during travel.
McKinney service
Call (469) 891-6883 or request a visit.
The visit
How a McKinney call runs
Secure the door before anything else
The door is clamped or blocked in position so it cannot drop or shift, and the opener is disconnected. On a crooked door this is the step that prevents the repair from becoming an incident.
Determine broken versus derailed
A snapped cable and a cable that came off its drum look similar from the driveway and are different repairs. We identify which happened and, if it derailed, what stopped the door in the first place, because the underlying cause matters.
Release tension and remove
Springs are unwound with winding bars so the cables go slack, then the bottom bracket end is freed and the old cable is removed from the drum. The drum, the shaft, the bearing, and the bottom fixture are inspected while they are accessible.
Install matched cables and set the drums
Cables are replaced as a pair in the correct diameter and length for the door height, seated in the drum grooves, and set to equal tension on both sides with the shaft locked so neither side takes up more than the other.
Rewind, test by hand, then by opener
Springs are wound to the correct turn count, the door is run by hand and checked for square travel at several heights, and only then is the opener reconnected, its travel and force reset, and the safety reversal tested.
On the job
Broken Cable Repair in the field
Questions
Broken Cable Repair in McKinney
Should both cables be replaced or just the failed one?
Both. They were installed together, they have taken the same number of cycles, and they wear at the same two points. Replacing one leaves a new cable working against an old one of slightly different effective length, which is exactly the condition that racks the door in the track. The material cost of the second cable is small relative to the labor already being performed.
How long does cable replacement take?
Generally one to two hours for a straightforward pair replacement, including unwinding and rewinding the springs and setting drum tension. It runs longer when the failure has bent a bottom bracket, scored a drum, or bowed a section of track, since those have to be corrected before the new cable will run true.
How often do cables need replacing?
There is no fixed interval. Cables typically outlast at least one set of springs, and many doors go a decade or more. What shortens their life is misalignment at the drum, corrosion at the bottom of the run from a wet slab, and repeated events where the door lands on an obstruction and the cable goes slack.
Can I put the cable back on the drum myself?
This is one to leave alone, and not because it is complicated to understand. The springs are wound, the bottom bracket is under load, and correcting drum tension requires locking the shaft while the set screws are loose. If the shaft turns while those screws are out, the counterbalance releases. The physical risk is real and the correct tooling is specific.
Can you replace a cable without touching the springs?
No, not properly. The cable is what transmits spring tension to the door, so the tension has to come off before the cable can be freed at either end. Any method that appears to skip that step is working around a loaded system, which is where injuries come from.
Talk to a technician now
Broken Cable Repair in McKinney and across Collin County.