Carrollton, Denton County
Broken Cable Repair in Carrollton, TX
Cable replacement is one of the least expensive repairs on a garage door and one of the most expensive to postpone. A door running on one cable twists in the tracks, gouges the vertical track, bends the bottom bracket, and can pull rollers out entirely, and at that point the invoice in Carrollton is no longer about a cable.
- Same-day service available
- 10+ years serving Dallas
- Free on-site estimates
- 15% off current repairs
The bottom bracket is where people get hurt
Both bottom brackets are under the full tension of the counterbalance whenever the door is closed, because that is exactly where the cables pull. Factory labels on those brackets warn against removing them, and the warning is accurate. If the bolts are backed out while the springs are wound, the bracket departs the door under load with the cable attached. Correct sequence is to unwind the springs with winding bars first, so the cables go slack, and only then work on the bracket. This is the same reason a broken cable is not a job to improvise on a Saturday: the intact side is still fully loaded.
Equal tension is what makes the door lift square
Replacing a cable is only half the job. Both cables have to be seated in their drums with the same number of wraps and the same tension, so that both bottom corners of the door lift at the same rate. If one drum is set even slightly differently, the door racks in the tracks on every cycle, which wears the rollers on the lagging side, marks the track, and eventually puts the door out of square permanently. Setting that tension involves loosening the drum set screws with the shaft locked, taking up the slack evenly on both sides, and re tightening onto the flats of the shaft. It is a fussy step and it is the difference between a repair that lasts and one that comes back.
What we check while the system is apart
Cable failure often leaves evidence elsewhere. The drum grooves may be scored where the cable rode out of place. The shaft can be scarred where a cable wrapped it. The bottom bracket rollers may be bent from the door dropping on one side. The vertical track frequently has a bright gouge or a bowed section where a roller was pulled sideways against it. Bearings get inspected because they are only accessible during this work. We report what we find with the reasoning, and we separate what needs replacing from what is simply cosmetic damage.
Broken Cable Repair for Carrollton homes
Mostly 1980s-90s two-story tract homes with attached two-car garages; the standard 16x7 sectional door with a 1/2 hp opener covers the large majority of service calls in the city.
We cover ZIP codes 75006, 75007 and 75010.
Downtown Carrollton, Josey Ranch and Rosemeade account for a steady share of our Carrollton work.
Josey Ranch Lake is a useful marker: if you are near it, we cover you.
About 135,456 people live in Carrollton, in Denton County.
Please do not attempt this one yourself
A torsion spring holds several hundred pounds of stored energy even when the door is down. Releasing that energy without the correct winding bars is how people lose fingers. If a spring has snapped, leave the door closed and call us.
What you are probably seeing
- One corner of the door hangs lower than the other, whether open or closed.
- A cable is visibly loose, hanging slack, or coiled off the drum.
- You can see broken strands sticking out of the cable, often described as fuzzy or whiskered.
- The door lifts unevenly and binds partway up.
- Loud scraping or popping from one side of the door during travel.
Carrollton service
Call (469) 891-6883 or request a visit.
The visit
How a Carrollton call runs
Secure the door before anything else
The door is clamped or blocked in position so it cannot drop or shift, and the opener is disconnected. On a crooked door this is the step that prevents the repair from becoming an incident.
Determine broken versus derailed
A snapped cable and a cable that came off its drum look similar from the driveway and are different repairs. We identify which happened and, if it derailed, what stopped the door in the first place, because the underlying cause matters.
Release tension and remove
Springs are unwound with winding bars so the cables go slack, then the bottom bracket end is freed and the old cable is removed from the drum. The drum, the shaft, the bearing, and the bottom fixture are inspected while they are accessible.
Install matched cables and set the drums
Cables are replaced as a pair in the correct diameter and length for the door height, seated in the drum grooves, and set to equal tension on both sides with the shaft locked so neither side takes up more than the other.
Rewind, test by hand, then by opener
Springs are wound to the correct turn count, the door is run by hand and checked for square travel at several heights, and only then is the opener reconnected, its travel and force reset, and the safety reversal tested.
On the job
Broken Cable Repair in the field
Questions
Broken Cable Repair in Carrollton
Should both cables be replaced or just the failed one?
Both. They were installed together, they have taken the same number of cycles, and they wear at the same two points. Replacing one leaves a new cable working against an old one of slightly different effective length, which is exactly the condition that racks the door in the track. The material cost of the second cable is small relative to the labor already being performed.
Is a broken cable dangerous?
The door itself becomes unpredictable, which is the practical danger. With one cable gone, the counterbalance is pulling on one corner, the door twists in the tracks, and it can jam partway or come off the track entirely. The other genuine hazard is the repair itself, because the bottom brackets and the intact cable are still under full spring tension until the springs are unwound.
How long does cable replacement take?
Generally one to two hours for a straightforward pair replacement, including unwinding and rewinding the springs and setting drum tension. It runs longer when the failure has bent a bottom bracket, scored a drum, or bowed a section of track, since those have to be corrected before the new cable will run true.
Can I put the cable back on the drum myself?
This is one to leave alone, and not because it is complicated to understand. The springs are wound, the bottom bracket is under load, and correcting drum tension requires locking the shaft while the set screws are loose. If the shaft turns while those screws are out, the counterbalance releases. The physical risk is real and the correct tooling is specific.
Can you replace a cable without touching the springs?
No, not properly. The cable is what transmits spring tension to the door, so the tension has to come off before the cable can be freed at either end. Any method that appears to skip that step is working around a loaded system, which is where injuries come from.
Talk to a technician now
Broken Cable Repair in Carrollton and across Denton County.